Skip to main content
Log in
Experimental Mechanics

An International Journal Integrating Experimental Methods with the Mechanical Behavior of Materials and Structures

Publishing model:

Experimental Mechanics - Top Downloaded Articles of 2022

Ncorr: Open-Source 2D Digital Image Correlation Matlab Software (this opens in a new tab)

J. Blaber, B. Adair & A. Antoniou

Structural Analysis of a Dragonfly Wing (this opens in a new tab)

S. R. Jongerius & D. Lentink

A Review of Speckle Pattern Fabrication and Assessment for Digital Image Correlation (this opens in a new tab)

Y.L. Dong & B. Pan

Experimental and Analytical Study of Free-Fall Drop Impact Testing of Portable Products (this opens in a new tab)

E. Tempelman, M. M. S. Dwaikat & C. Spitás

Correction of Scanning Electron Microscope Imaging Artifacts in a Novel Digital Image Correlation Framework (this opens in a new tab)

S. Maraghechi et al.

Recent Progress in Digital Image Correlation (this opens in a new tab)

B. Pan

Super Resolution Digital Image Correlation (SR-DIC): an Alternative to Image Stitching at High Magnifications (this opens in a new tab)

R. S. Hansen, D. W. Waldram, T. Q. Thai & R. B. Berke

Measuring Residual Strain and Stress in Thermal Spray Coatings Using Neutron Diffractometers (this opens in a new tab)

N. H. Faisal, R. Ahmed, A. K. Prathuru, A. Paradowska, & T. L. Lee

Determining Dynamic Properties of Elastomer-Dampers by Means of Impact Testing (this opens in a new tab)

T. Rapp, G. Jacobs, J. Berroth & J. Guenther

Why Is It So Challenging to Measure Residual Stresses ? (this opens in a new tab)

G. S. Schajer, M. B. Prime & P. J. Withers

DIC Challenge 2.0: Developing Images and Guidelines for Evaluating Accuracy and Resolution of 2D Analyses (this opens in a new tab)

P. L. Reu et al.

Direct Measurement of the Transverse Modulus of Carbon Fibres (this opens in a new tab)

S. Wong, A. P. Pierlot, A. M. Abbott & J. A. Schutz

Residual Stresses from Incremental Hole Drilling Using Directly Deposited Thin Film Strain Gauges (this opens in a new tab)

S. Heikebrügge, R. Ottermann, B. Breidenstein, M.C. Wurz & F. Dencker

Effect of Filling Pattern on the Tensile and Flexural Mechanical Properties of FDM 3D Printed Products (this opens in a new tab)

B. Akhoundi & A. H. Behravesh

The Symmpact: A Direct-Impact Hopkinson Bar Setup Suitable for Investigating Dynamic Equilibrium in Low-Impedance Materials (this opens in a new tab)

P. Jakkula, G. C. Ganzenmüller, S. Beisel, P. Rüthnick & S. Hiermaier

Digital Volume Correlation: Review of Progress and Challenges (this opens in a new tab)

A. Buljac et al.

J-Integral Calculation by Finite Element Processing of Measured Full-Field Surface Displacements (this opens in a new tab)

S.M. Barhli, M. Mostafavi, A.F. Cinar, D. Hollis & T.J. Marrow

DIC Challenge: Developing Images and Guidelines for Evaluating Accuracy and Resolution of 2D Analyses (this opens in a new tab)

P. L. Reu et al.

Residual Stress Measurements in Extreme Environments for Hazardous, Layered Specimens (this opens in a new tab)

B. C. Benefiel et al.

Size-Dependent Fracture Characteristics of Intermetallic Alloys (this opens in a new tab)

Arun Raina

Navigation