Thermomechanics & Infrared Imaging, Inverse Problem Methodologies and Mechanics of Additive & Advanced Manufactured Materials, Volume 6

1. Front Matter

   Pages i-vii

   PDF

2. Evaluation of the Maximum Allowable Hole Depth for IHD of GFRP Laminates

   • Robert G. Reid, Teubes C. Smit

   Pages 1-8

3. Analysis of Intrinsic Dissipations and Fatigue Behaviour ofSteelsby Measuring Thermal and Mechanical Signals DuringFatigueTests

   • Rosa De Finis, Davide Palumbo, Umberto Galietti

   Pages 9-17

4. Analysis of the Fracture Mechanics Behaviour of an Additive Manufactured Titanium Alloy Via a Thermography-Based Technique

   • Rosa De Finis, Aleksander Sendrowicz, Aleksander Omholt Myhre, Filippo Berto, Alexei Vinogradov, Umberto Galietti

   Pages 19-26

5. Non-destructive Evaluation of Hot-Spots Using the IR Thermography

   • V. E. L. Paiva, R. B. Vieira, G. L. G. Gonzáles, J. C. Diniz, L. C. Mendes, J. L. F. Freire

   Pages 27-34

6. Modeling Micrometeoroid and Orbital Debris Impact on Composite Truss Tubes

   • Greyson Hodges, Mark Pankow

   Pages 35-38

7. Identification of Subsurface Damage in Multidirectional Composite Laminates Using Full-Field Imaging

   • R. Ruiz-Iglesias, G. Ólafsson, O. T. Thomsen, J. M. Dulieu-Barton

   Pages 39-42

8. Detection Analysis for Sub-Superficial Defects in Additive Manufactured Metal Samples by Means of Flash Thermography

   • Ester D’Accardi, Davide Palumbo, Vito Errico, Andrea Fusco, Andrea Angelastro, Giuseppe Danilo Addante et al.

   Pages 43-54

9. The Miura Ori Geometry: From Brilliant Theory to Surprising Auxetic Properties

   • Antonio Baldi, Pietro Maria Santucci, Giorgio Carta, Michele Brun, Daniele Lai

   Pages 55-59

10. Flow Visualization in the Extrusion of Highly Filled Polymer Composites for Additive Manufacturing

    • Mike O’Donnell

    Pages 61-67

11. Additive Manufacturing of Graded Voronoi Cellular Structures for Increased Design Flexibility

    • Vijendra Gupta, Addis Kidane, Michael Sutton

    Pages 69-74

12. Investigation of Microstructure and Mechanical Properties of Additive Manufacturing Fabricated Oxide Dispersion Strengthening (ODS) IN718 Alloys

    • Changyu Ma, Kyle Rozman, Douglas Straub, Omer Dogan, Sarwesh Narayan Parbat, Minking Chyu et al.

    Pages 75-83

13. A Nondestructive Evaluation Technique to Measure Axial Stress in Continuous Welded Rails

    • Alireza Enshaeian, Matthew Belding, Piervincenzo Rizzo

    Pages 85-93

Thermomechanics & Infrared Imaging, Inverse Problem Methodologies and Mechanics of Additive & Advanced Manufactured Materials, Volume 6 of the Proceedings of the 2022 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the sixth volume of six from the Conference, brings together contributions to this important area of research and engineering.  The collection presents early findings and case studies on a wide range of areas, including:

 

Test Design and Inverse Method Algorithms

Inverse Problems: Virtual Fields Method

Material Characterizations Using Thermography

Fatigue, Damage & Fracture Evaluation Using Infrared Thermography

Residual Stress

Mechanics of Additive & Advanced Manufactured Materials

• Test Design and Inverse Method Algorithms
• Inverse Problems: Virtual Fields Method
• Material Characterizations Using Thermography
• Residual Stress
• Mechanics of Additive & Advanced Manufactured Materials

• University of Waikato, Waikato, New Zealand

  Rachael C Tighe

• Forest Products Laboratory, USDA, Forest Service, Madison, USA

  John Considine

• Sandia National Laboratories, Albuquerque, USA

  Sharlotte L.B. Kramer

• University of Louisville, Louisville, USA

  Tom Berfield

Rachael Tighe, University of Waikato, New Zealand; John Considine, United States Department of Agriculture, Forest Service, Forest Products Laboratory, WI, USA; Sharlotte L.B. Kramer, Sandia National Laboratories, NM, USA; Tom Berfield, University of Louisville, KY, USA

Policies and ethics