Surface Engineering

1. Front Matter

   Pages i-xxii

   PDF

2. Modelling, Simulation and Characterisation of Surfaces

   1. Characterisation and Quality Control of Surface Treatments and Coatings

      • K. Stevens

      Pages 1-13

   2. Microstructural Preparation and the Achievement of a Representative Surface

      • I. A. Bucklow, P. Morrell

      Pages 14-21

   3. Photothermal Reflectance Investigation of Implanted Silicon

      • I. A. Vitkin, C. Christofides, A. Mandelis

      Pages 22-28

   4. The Erosion-Corrosion of a Nitrocarburized Low Alloy Steel in a Simulated FBC Environment

      • P. M. Rogers, I. M. Hutchings, J. A. Little

      Pages 29-38

   5. Comparison of Fractal and Conventional Topographic Analysis of Electric Discharge Machined Ceramic Surfaces

      • C. A. Brown, D. F. Dauw, G. Savary

      Pages 39-51

3. Surface Preparation and Protection

   1. Corrosion Protection through Salt Bath Nitriding

      • J. R. Easterday

      Pages 52-61

   2. Protection of Surfaces of Natural Stone and Concrete through Polymers

      • P. J. Koblischek

      Pages 62-71

   3. The Influence of Directivity of Machining Marks on Grindability and Wear of Honed Surfaces

      • A. F. Budzyński

      Pages 72-81

   4. Wear Resistant Surfaces with a Hardphase Gradient

      • H. Berns, A. Fischer, Ch. v. Nguyen

      Pages 82-90

4. Adhesive Bonding and Bondface Characterisation

   1. Surface Characterization and High-Temperature Adhesive Bonding of Carbon Fiber-Polyimide Matrix Composites

      • D. J. D. Moyer, J. P. Wightman

      Pages 91-99

   2. Contact Angles on Imperfect Solid Surfaces

      • J. Gaydos, C. J. Budziak, D. Li, A. W. Neumann

      Pages 100-112

   3. Engineering the Interphase in Reinforced Plastics

      • A. Khelawan, M. R. Piggott

      Pages 113-119

   4. Ferroelectric Thin Films from Metallo-organics: The Influence of Different Atmospheres during RTA Processing

      • Y. Shi, E. Sánchez-Carambot, W. Otaño, L. J. Martínez-Miranda, J. J. Santiago-Avilés

      Pages 120-125

   5. Ultrasonic Verification of Surface Treatment Adequacy in Metal-to-Metal Adhesive Joints

      • P. Dickstein

      Pages 126-135

   6. The Unidirectional Tensile Characteristics of Ion-Nitrided and Ion-Carbonitrided Surface Layer of 40CrNiMo

      • Guan Delin, Yu Zhiwei, Zhang Hongtien, Yang Lieyu

      Pages 136-145

5. Surface Effects on Implantation

   1. Friction and Metal Transfer in Sliding Aluminum against Ion-Implanted Steel

      • P. C. Nautiyal, J. A. Schey

      Pages 146-155

   2. The Effect of Ion Implantation on the Fretting Fatigue Properties of Titanium Alloy Fan and Compressor Blades

      • J. E. Elder, R. Pishva, W. Doswell, G. Weatherly, W. Wallace

      Pages 156-166

   3. Martensitic Transformation in 304 Stainless Steel after Implantation with Neon

      • J. Y. Xu, B. J. van Brussel, J. Noordhuis, P. M. Bronsveld, J. Th. M. de Hosson

      Pages 167-176

   4. Elevated Temperature Ion Implantation: A New Direction for Surface Engineering

      • F. J. Worzala, J. R. Conrad, R. A. Dodd, M. Madapura, K. Sridharan

      Pages 177-187

Integral geometry deals with the problem of determining functions by their integrals over given families of sets. These integrals de?ne the corresponding integraltransformandoneofthemainquestionsinintegralgeometryaskswhen this transform is injective. On the other hand, when we work with complex measures or forms, operators appear whose kernels are non-trivial but which describe important classes of functions. Most of the questions arising here relate, in one way or another, to the convolution equations. Some of the well known publications in this ?eld include the works by J. Radon, F. John, J. Delsarte, L. Zalcman, C. A. Berenstein, M. L. Agranovsky and recent monographs by L. H¨ ormander and S. Helgason. Until recently research in this area was carried out mostly using the technique of the Fourier transform and corresponding methods of complex analysis. In recent years the present author has worked out an essentially di?erent methodology based on the description of various function spaces in terms of - pansions in special functions, which has enabled him to establish best possible results in several well known problems.

• complex analysis
• geometry

• Department of Mechanical Engineering, University of Toronto, Toronto, Canada

  S. A. Meguid

Policies and ethics