Advances in Cryogenic Engineering

1. Front Matter

   Pages i-iv

   PDF

2. Experimental Investigation of Thermal Shock Wave Induced by Gas Dynamic Shock Wave Impingement

   • H. S. Yang, H. Nagai, N. Takano, M. Murakami

   Pages 961-968

3. Approximate Solution for Transient Heat Transfer in Static Turbulent He II

   • B. Baudouy

   Pages 969-976

4. A He II Heat Exchanger Test Unit Designed for the LHC Interaction Region Magnets

   • Ch. Darve, Y. Huang, J. Kerby, T. Nicol, T. Peterson

   Pages 977-984

5. A Facility for Accurate Heat Load and Mass Leak Measurements on Superfluid Helium Valves

   • A. Bézaguet, L. Dufay, G. Ferlin, R. Losserand-Madoux, A. Perin, G. Vandoni et al.

   Pages 985-992

6. Flow in Horizontal Two Phase He II /Vapor

   • S. W. Van Sciver, J. S. Panek, D. Celik

   Pages 993-1000

7. Numerical Study of Two-Phase Helium II Stratified Channel Flow

   • Y. Xiang, N. N. Filina, S. W. Van Sciver, J. G. Weisend II, S. Wolff

   Pages 1001-1008

8. He II Two Phase Flow in an Inclinable 22 m Long Line

   • B. Rousset, A. Gauthier, B. Jager, R. van Weelderen

   Pages 1009-1016

9. Investigation of Noisy Film Boiling Under Various Thermal Conditions in He II

   • P. Zhang, M. Murakami, R. Z. Wang, Y. Takashima

   Pages 1017-1024

10. Thin-Film Thermometer and Heater Design for the Detection and Generation of Second Sound Shock Pulses

    • D. K. Hilton, M. R. Smith, S. W. Van Sciver

    Pages 1025-1032

11. Steady State Heat Transfer Characteristics in He I and He II with a Copper Surface

    • A. Iwamoto, R. Maekawa, T. Mito, S. Satoh

    Pages 1033-1040

12. Film Boiling on a Horizontal Cylinder in Saturated and Subcooled Helium II

    • K. Hama, K. Hata, M. Shiotsu

    Pages 1041-1048

13. Study of Shock Waves and Phase Transition in He II by Using a Superfluid Shock Tube Facility

    • H. Nagai, N. Takano, H. S. Yang, M. Murakami

    Pages 1049-1056

14. Experimental Study on the Transition of He II Boiling Modes with the Hydrostatic Pressure Around the Lambda Temperature

    • Y. Takashima, M. Murakami, T. Toyoshima

    Pages 1057-1064

15. Transient Heat Transfer Produced by a Stepwise Heat Input to a Flat Plate on One End of a Rectangular Duct Containing Pressurized Helium II

    • M. Shiotsu, K. Hata, K. Hama, Y. Shirai

    Pages 1065-1072

16. Critical Heat Fluxes on a Flat Plate Attached to One End of a Rectangular Duct Containing Pressurized He II

    • H. Tatsumoto, K. Hata, K. Hama, Y. Shirai, M. Shiotsu

    Pages 1073-1080

17. Inferring the Structure of Porous Materials Using Superfluid Helium

    • H. A. Snyder

    Pages 1081-1088

18. Heat Transfer Peculiarities and Their Application to Non-Drained Liquified Gas Storage

    • Zh. A. Suprunova, V. E. Seriogin, A. V. Latchenko

    Pages 1089-1094

19. Thermodynamic Analysis of Temperature Increase and Energy Consumption in a Cryogenic Crusher

    • Y. Liang, W. Tang, P. R. Yang, Y. Y. Guo

    Pages 1095-1102

20. Stability and Control of Supercritical Helium Flow in the LHC Circuits

    • E. Hatchadourian

    Pages 1103-1110

In recent years, the technology of cryogenic comminution has been widely applied in the field of chemical engineering, food making, medicine production, and particularly in recycling of waste materials. Because of the increasing pollution of waste tires and the shortage of raw rubber resource, the recycling process for waste rubber products has become important and commercially viable. This technology has shown a great number of advantages such as causing no environmental pollution, requiring low energy consumption and producing high quality products. Hence, the normal crusher which was used to reclaim materials, such as waste tires, nylon, plastic and many polymer materials at atmospheric 12 temperature is being replaced by a cryogenic crusher. • In the cryogenic crusher, the property of the milled material is usually very sensitive to temperature change. When a crusher is in operation, it will generate a great deal of heat that causes the material temperature increased. Once the temperature increases over the vitrification temperature, the material property will change and lose the brittle behavior causing the energy consumption to rise sharply. Consequently, the comminution process cannot be continued. Therefore, it is believed that the cryogenic crusher is the most critical component in the cryogenic comminution system. The research on the temperature increase and energy consumption in the cryogenic crusher is not only to reduce the energy consumption of the crasher, but also to reduce the energy consumption of the cryogenic system.

• Recycling
• chemical engineering
• electronics
• heat transfer
• pollution
• polymer
• production

about previous volumes:
`The Advances in Cryogenic Engineering series provides a timely and authoritative entrée to the field for the outsider. For the insider, it is a must.'
Materials Science and Engineering
`Provides in-depth coverage of current research on technical materials of primary interest in the cryogenic engineering community, reviews important breakthroughs of the past, and outlines directions for future research.'
Cryogenic Information Report
`An interdisciplinary review of all areas of low-temperature technology, this significant series annually updates existing knowledge of cryogenic processes, equipment, instrumentation, properties, and applications....The literature source for many important new discoveries in the field.'
IEEE Spectrum

• AMAC International, Inc., Newport News, USA

  Quan-Sheng Shu

Policies and ethics