Editors:
- Reports on cutting-edge research on (un)conventional manufacturing
- Discusses current problems connected to climate change
- Highlights important points of contact between academic research and industrial development
- Covers a broad range of fabrication processes
Part of the book series: Lecture Notes in Mechanical Engineering (LNME)
Conference series link(s): ICMEM: International Conference on Manufacturing Engineering and Materials
Conference proceedings info: ICMEM 2021.
Buy it now
Buying options
Tax calculation will be finalised at checkout
Other ways to access
This is a preview of subscription content, log in via an institution to check for access.
Table of contents (34 papers)
-
Front Matter
-
Water Jet Session
-
Front Matter
-
-
Manufacturing Engineering Session
-
Front Matter
-
About this book
This book reports on cutting-edge research and technologies in the field of advanced manufacturing and materials, with a special emphasis on unconventional machining process, rapid prototyping and biomaterials. It gathers contributions to the International Conference on Manufacturing Engineering and Materials (ICMEM 2020), which was originally planned in June 2020, but will actually take place in 2021, in Nový Smokovec, Slovakia, because of the Covid-19 pandemic. Despite the challenging times, submitted contributions were peer-reviewed, and upon a careful revision, included in this book, which covers advances that are expected to increase the industry’s competitiveness with regard to sustainable development and preservation of the environment and natural resources. Condition monitoring, industrial automation, and diverse fabrication processes such as welding, casting and molding, as well as tribology and bioengineering, are just a few of the topics discussed in the book’s wealth ofauthoritative contributions. A special emphasis is given to problems connected to climate change and solution manufacturer and engineers may adopt and develop to prevent and cope with them.
Keywords
- Wear Simulation
- Engine Friction Model
- Industrial Modeling and Simulation
- Systems Modeling
- Rapid Prototyping
- Evaluation of Material Properties
- Polyethylene Insert
- Materials for Knee Prosthesis
- Water Jet Technology
- Plasma Cutting Technology
- Laser Cutting Technology
- New Materials For Manufacturing
- ICMEM 2019
Editors and Affiliations
-
Faculty of Manufacturing Technologies TUKE, Bayerova 1, Slovakia
Sergej Hloch
-
Institute of Geonics of the CAS, Ostrava, Czech Republic
Dagmar Klichová
-
High-Pressure Waterjet Technology, Steinbeis Consulting Center, Horgau, Germany
Frank Pude
-
Opole University of Technology, Faculty of Mechanical Engineering, Opole, Poland
Grzegorz M. Krolczyk
-
Indian Institute of Technology, Indian School of Mines, Dhanbad, India
Somnath Chattopadhyaya
Bibliographic Information
Book Title: Advances in Manufacturing Engineering and Materials II
Book Subtitle: Proceedings of the International Conference on Manufacturing Engineering and Materials (ICMEM 2020), 21–25 June, 2021, Nový Smokovec, Slovakia
Editors: Sergej Hloch, Dagmar Klichová, Frank Pude, Grzegorz M. Krolczyk, Somnath Chattopadhyaya
Series Title: Lecture Notes in Mechanical Engineering
DOI: https://doi.org/10.1007/978-3-030-71956-2
Publisher: Springer Cham
eBook Packages: Engineering, Engineering (R0)
Copyright Information: The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG 2021
Softcover ISBN: 978-3-030-71955-5Published: 17 March 2021
eBook ISBN: 978-3-030-71956-2Published: 16 March 2021
Series ISSN: 2195-4356
Series E-ISSN: 2195-4364
Edition Number: 1
Number of Pages: XVI, 412
Number of Illustrations: 58 b/w illustrations, 208 illustrations in colour
Topics: Manufacturing, Machines, Tools, Processes, Materials Engineering, Energy Policy, Economics and Management