Journal of Materials Science: Materials in Engineering

Featured Article: Effect of concentration, aging, and annealing on sol gel ZnO and Al-doped ZnO thin films

Transparent thin film Our most cited article from 2020 reports on the optical and structural properties of one of the most important transparent conductive oxides for applications in light-emitting diodes and solar cells. The latest research from the Titan Tech Energy research team reveals improved concentration, aging, and annealing times for gel zinc oxide (ZnO) and Al-doped ZnO thin films, driving it towards becoming a high-quality, low defect film, strengthening its application in both research and industry.

Read the full article here.

Use of Taguchi method for high energy ball milling of CaCO₃

Authors: Maya Radune, Svetlana Lugovskoy, Yaniv Knop and Avigdor Yankelevitch

Content type: Original Paper 4 February 2022
Experimental investigation into the effect of surface roughness and mechanical properties of 3D-printed titanium Ti-64 ELI after heat treatment

Authors: L. Lebea, H. M. Ngwangwa, D. Desai and F. Nemavhola

Content type: Review Article 17 November 2021
Injection-molded natural fiber-reinforced polymer composites–a review

Authors: M. S. Rabbi, Tansirul Islam and G. M. Sadiqul Islam

Content type: Review Article 10 November 2021
Plane wave in non-local semiconducting rotating media with Hall effect and three-phase lag fractional order heat transfer

Authors: Iqbal Kaur and Kulvinder Singh

Content type: Original Paper 26 September 2021
Microstructural and mechanical studies of feedstock material in continuous extrusion process

Authors: Tariku Desta, Devendra Kumar Sinha, Perumalla Janaki Ramulu and Habtamu Beri Tufa

Content type: Original Paper 6 September 2021

Most recent articles RSS

View all articles

Robotic arc welding sensors and programming in industrial applications

Authors: P Kah, M Shrestha, E Hiltunen and J Martikainen

Content type: Review Article 17 July 2015
Investigation of weld defects in friction-stir welding and fusion welding of aluminium alloys

Authors: Paul Kah, Richard Rajan, Jukka Martikainen and Raimo Suoranta

Content type: Review article 22 December 2015
Numerical and heat transfer analysis of shell and tube heat exchanger with circular and elliptical tubes

Authors: J. Bala Bhaskara Rao and V. Ramachandra Raju

Content type: Original article 23 May 2016
Selection of suitable passive cooling strategy for a subtropical climate

Authors: Ahmed-Shams Forruque Ahmed, Khan-Mohammad Masud Kamal Khan, Amanullah-Amanullah Maung Than Oo and Rasul-Mohammad Golam Rasul

Content type: Original Article 26 September 2014

The Erratum to this article has been published in International Journal of Mechanical and Materials Engineering 2015 10:5
Properties of ceramic-reinforced aluminium matrix composites - a review

Authors: Dipti Kanta Das, Purna Chandra Mishra, Saranjit Singh and Ratish Kumar Thakur

Content type: Review Article 20 August 2014

Most accessed articles RSS

View all articles

Additive Manufacturing in Healthcare and Pharmaceutical Industries.
Guest Edited by: Prof. Faris Tarlochan, Dr. Dimitrios Lamprou, Dr. Eneko Larrañeta

Nanomaterials: Synthesis, processing, properties, and applications.
Guest Edited by: Dr. Rahul Trivedi & Dr. Rosa Diaz

Tribology of components in mechanical systems.
Guest Edited by: Prof. Franco Concli & Prof. Thomas Lohner

Aims and Scope

The Journal of Materials Science: Materials in Engineering is a peer-reviewed, international and interdisciplinary journal that provides a forum for cross-disciplinary research contributions covering a broad spectrum of issues pertaining to the mechanical and machining properties of materials as well as materials science, and how they apply to materials used in equipment and structures.

Read the full Aims and Scope here

Article Processing Charges (APCs)

Open access publishing is not without costs. Journal of Materials Science: Materials in Engineering therefore levies an article-processing charge of £1090.00/$1590.00/€1340.00 for each article accepted for publication.

For further details, see our article-processing charge page.

Benefit from our free funding service

We offer a free open access support service to make it easier for you to discover and apply for article-processing charge (APC) funding.

Learn more here.

How was your experience today?

Rating Please select one rating

Awful

Bad

Good

Great

Thank you for your feedback.

Tell us why (opens in a new tab)

Journal of Materials Science: Materials in Engineering

Featured Article: Effect of concentration, aging, and annealing on sol gel ZnO and Al-doped ZnO thin films

Use of Taguchi method for high energy ball milling of CaCO₃

Experimental investigation into the effect of surface roughness and mechanical properties of 3D-printed titanium Ti-64 ELI after heat treatment

Injection-molded natural fiber-reinforced polymer composites–a review

Plane wave in non-local semiconducting rotating media with Hall effect and three-phase lag fractional order heat transfer

Microstructural and mechanical studies of feedstock material in continuous extrusion process

Robotic arc welding sensors and programming in industrial applications

Investigation of weld defects in friction-stir welding and fusion welding of aluminium alloys

Numerical and heat transfer analysis of shell and tube heat exchanger with circular and elliptical tubes

Selection of suitable passive cooling strategy for a subtropical climate

Properties of ceramic-reinforced aluminium matrix composites - a review

Aims and Scope

Article Processing Charges (APCs)

Benefit from our free funding service

Follow

Annual Journal Metrics

Latest Tweets